Tag: Ruideng

Voltlog #290 – Riden RD6006 Output Noise Using Recommended Power Supply NVVV S-400-60

Welcome to a new Voltlog, this will be a rather short video cause I will only be addressing one short subject regarding the Riden RD6006 ripple noise. In my review of this power supply in Voltlog #284 I did measure the output ripple but that was measured while using a transformer to power the unit. 

That transformer has very little output noise so the results we obtain can be considered best case scenarios but this may vary in practice, especially if you are using the recommended switch mode power supply. The output of that power supply may not be as clean as the one from the transformer so in this video I’m going to measure the output noise with the switch mode power supply installed.

I’m using the recommended NVVV 400W 60V 6.6A rated power supply, this is what RuiDeng officially recommends to use with their power supply kit. In Voltlog 284 part 3 I took a look inside this power supply so I will link that video on screen if you want to check it out.

Voltlog #284 – Riden RD6006 Power Supply Review

Welcome to a new Voltlog, if you’ve been watching the channel for a while you might know I’m a fan of the gopher power supply units, I think they are great value for money, they’re simple and they have good specs, in fact I reviewed their latest revision in Voltlog #255 and it had very low noise at the output, even though it is a switch mode power supply. They’re pretty compact, they don’t take up much space on the bench so what’s there not to like about these?

But in recent years there’s been another company which has slowly built-up a name among hobbyists due to their really low priced power supply modules, the name of the company is RuiDeng and they’ve been selling these compact switch mode power supply modules for $20 to $30 for years. They were not great specs, the quality was not great, you needed an external power supply unit but they had a bunch of functionality built into that color TFT display and they were cheap so everyone gave them a try

Now RuiDeng has developed and released a new model RD6006 which resembles a real bench power supply. It has a bigger front panel and it comes with a separate enclosure and power supply unit which are optional.

Voltlog #248 – Atorch Q7 USB Meter/Load With QI Wireless Charging

So this load is built with 3 active pcb’s as well as a fourth passive one as a front panel. They are joined with these brass standoffs and I think the standoffs act as circuit paths as well because I see no wires between the different levels. In order to get the alignment right during assembly the designer of these pcbs, made these corners rounded while these ones are diagonally cut and you can see these features along an entire side. This is a neat solution overall because it saves cost and as long as the screws are tight these should provide adequate connection.

Voltlog #247 – InTheMail

Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time. We’re going to start with this small module, at first when I ordered it I didn’t fully understood what it does but now after doing a bit of research for this mailbag it seems this is an immobiliser emulator for the VAG group. So am immobiliser is a security component of your car that will not let the ECU start the engine unless a certain key or token is present. And there might be valid reasons why you might need this emulator, for example if the immobiliser is broken, you can supposably cancel it and start the engine with this emulator or if you exchange the motor/ecu combo once again it might not be possible to use the old immobiliser and so an emulator will help.

It talks over a K-line interface which is something specific to the automotive domain but it’s basically a form of serial interface. At first I thought this was going to emulate some kind of can bus and I was planning to play with it by scanning the bus but now I realize this is useless for me.

Voltlog #167 – InTheMail

Welcome to a new InTheMail the series that will touch both your passion for electronics and your bank account at the same time.

Here are links to all the products shown in this video:

Voltlog #131 – Measuring The Efficiency Of The Ruideng Kis3r33S DC-DC Converter

You might remember this small module from the previous InTheMail, this is the Ruideng dc-dc converter with a claimed efficiency of 95%. Now a figure of 95% efficiency is not unheard of these days, many dc-dc converters can achieve this with proper circuit design.

This particular model uses the MP2307 converter chip manufactured by Monolithic Power and if we take a look at their datasheet we can immediately see where they got the 95% efficiency figure they advertise.

If you own fancy equipment like a source/measure unit than one instrument can do all the measurements and data log the results as well but a source/measure is out of our budget so we will be using multimeters for this test.

Here are links where you can find the equipment used in this video:

Voltlog #130 – InTheMail

Last InTheMail video was published almost two months ago so I think you will appreciate this one where I got some interesting stuff from the usual Chinese sources.

Links for all the items shown in this video below: