Welcome to a new Voltlog, as the title says this will be a non-electronics mailbag, meaning I will show you what other stuff I am ordering and receiving by mail. A few days ago I created this poll on my youtube community page and asked where I should upload this kind of video, there were really two options, either upload to this channel or create a new one. I was kinda hoping for people to vote to upload them to the same channel because I don’t really want to manage a second channel and it’s also understandable if people vote for the same channel because they don’t need to perform other actions to subscribe to a second channel. And so it was decided to upload to the same channel but mark these videos as non-electronics mailbags.
Voltlog #270 – 11.11 Shopping Festival Discounts Real or Fake?
Welcome to a new Voltlog, this will be just a short video, I want to talk about the prices and the discounts that we get on shopping festivals, because most of us think and myself included here, we think the price cuts we get for these shopping festivals are not actually true, we tend to think prices are inflated some time ahead only to be discounted on that day which makes them go back to roughly the same price they normally sell for.
Even in my past video with shopping suggestions Voltlog #269, I got such comments and I don’t blame people for thinking this, because like I said, I tend to think the same but I also want to find out the truth so what I did some time ago, beginning of September to be more precise, I save some screenshots of various items that I was interested in from A
liexpress.
Today it’s the 11th, the sale started so we’ll compare prices before and after, to see if the sellers actually raised their prices before the sale and are we really getting any discounts today.
Voltlog #269 – 11.11 Shopping Suggestions For Makers
Welcome to a new Voltlog, it’s November and that means the biggest shopping event happening in Asia is coming up, I’m talking about the 11th of november. There are some numbers published for last years event and it seems they registered more than 30 billion in 24 hours in sales, yes you heard right, billions. So it’s a very big event with nice discounts and opportunities for makers like us to get some new gear. That’s why I prepared this video which will be published 1-2 days before the event so you can get some ideas of stuff that you could purchase. I assembled a list, these are products that I’ve tested and used myself which I think are good value for money and a nice addition to any hobbyist lab.
Voltlog #268 – RaspberryPi 10 Inch IPS HDMI Monitor 2560×1600 2K
Welcome to a new Voltlog, it’s product review time again, this time we’re taking a closer look at a 10 inch monitor with hdmi input. This is the box it comes in, the monitor has a resolution of 2560×1600, that’s about 2K resolution in the scheme of things, 300 pixels per inch density, 16:10 aspect ratio which I’m a fan of. My desktop monitor is also 16:10 and it works so much better for everyday activities but especially if you are doing any CAD design work. It’s an IPS panel so we should have good brightness, contrast and colors, it’s rated at 400 candela per sq meter. We also get built-in speakers and the HDMI supports video & audio so you should be able to get video and sound through the HDMI cable and that’s useful because we have built-in speakers on the monitor itself.
Voltlog #267 – 60W Ultrasonic Cleaner For PCBs (review)
Welcome to a new Voltlog, today we’re going to take a closer look at an ultrasonic cleaner. This is the 1.3 litre, model number I believe is Y-009, the ultrasonic power is 60W while the heating power is rated for 100W. Usable area I’ve measured to be 125x115x40mm depth which is not a lot but I’ve thought about it and this is pretty much all I need. 99% of the PCBs I design fit within these dimensions so it’s not worth getting a bigger ultrasonic cleaner because it will take up more space and it will use up more cleaning liquid, it would be a waste of resources.
Voltlog #266 – How To Check If Your Raspberry Pi 4 Is Throttling CPU
Welcome to a new Voltlog, today my raspberry pi 4 is again in the spotlight because I want to show you the different scenarios where the board could be throttling down the CPU frequency and how you can identify those. Because it might be a case where your raspberry pi is running slow on a particular task and you don’t know why because there is no built-in mechanism to let you know when the board is throttling down. There are logs which you can check but let’s be honest, few people actually check the logs for something like this.
Throttling of the cpu frequency occurs for good reasons, to protect the board or the cpu from overheating or to prevent any errors from occurring in the case of an under-voltage scenario which may lead to data loss or corruption. Luckily there is a way to check if your system is under one of these conditions, you can run this command on your raspberry pi.
Voltlog #265 – FT232H USB to JTAG/I2C/SPI Interface With Python & PyFtdi
Welcome to a new voltlog, today we’re going to be talking about this little board which I designed and assembled myself, it’s a breakout module for the FTDI FT232H which is a usb to serial converter but with a nice twist. This particular chip from FTDI has the built-in Multi-Protocol Synchronous Serial Engine (MPSSE short) which allows you to run a variety of synchronous serial protocols like JTAG, I2C, SPI or simple bit-banging of IOs. You can imagine it can be really useful to be able to interface with a sensor over I2C or SPI straight from your computer over USB through this interface. You wouldn’t need an arduino or other controller in the middle if you plan to do some data acquisition for example.
Voltlog #264 – Passive Heatsink Cooling For The Raspberry Pi 4
Welcome to a new Voltlog, here is my raspberry pi 4 which I got a few months ago when they released it and if you have one you might have noticed it gets quite hot especially when it has to do some processing. This newer processor, will get hot quick and the board alone cannot cope with all of this heat so what does it do? Well when the CPU temperature reaches 80 degrees Celsius it will start throttling down the CPU as a way of protecting itself from overheating and this will result in a loss of performance.
The Raspberry Pi 4 has a 1.5GHz quad-core 64-bit Arm Cortex-A72 CPU, that’s roughly three times the performance of the raspberry pi 3 cpu. That inevitably generates more heat. In the original plastic case just sitting idle, connected to a network, doing pretty much nothing, the raspberry pi4 when compared to a raspberry pi3 runs about 12 degrees hotter.
Voltlog #263 – InTheMail
Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time. We’re going to start with this big jar of flux paste. This is commonly referred to as “yellow paste”, the branding I believe is NT but if you search for yellow paste you will find it in various sizes. Banggood sells it in 150 gram jar and it has a good price of $4 with free shipping. I’ve seen other people use this stuff with good results so I decided to give it a try. I’m not sure if there are any fakes to this particular brand, but the ones from banggood seem to be the genuine stuff.
The consistency is that of a paste so I don’t think it would be easy to put this inside a syringe and use it that way. This works better if you pick it up with a toothpick or some tweezers. This is not rosin based or so they advertise, and it’s supposed to be a neutral PH,with low corrosion to your pcb and components. You will probably see me use this in a future video, until then, there will be a link in the description so you can order one.
Voltlog #262 – Is This The Future of Our Hobby?
To be honest I didn’t think we were going to have services like these available so cheap so fast. I mean yes I know pcb prices have been so low in the past couple of years that it no longer makes sense to etch your own PCBs, unless you are in a big hurry. But having smt assembly service so cheap? Soon enough it would not make sense to hand assemble these boards because it would be equally cheap to have them assembled at JLCPCB