Tag: Quick-Charge

Voltlog #273 – InTheMail

Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time. Before I get started I’m gonna take a second to reminding you to subscribe to the channel and hit the bell notification icon because that’s the only way you will know for sure when I upload new videos. Now let’s start with this small esp32 based development board, it has a built-in 1.14 inch color tft lcd and I think that’s a nice feature of this dev board because if you want to connect some sensors and see the readings in real time, you don’t need to wire a display externally it’s built-in.

Another cool feature is that we have built-in battery charging at 500mA and you can power this board through the provided two pin jst connector with a one cell lipo battery which will then charge when connected to power via the USB Type-C port. There is also a CP2104 for the usb to serial conversion and that makes it a pretty well balanced development board for the ESP32.

The board comes loaded with a test program from TTGO, it shows this image then cycles through red, green, blue on the LCD which is a good idea because you can verify the board is functioning ok after the long journey it takes from the market in shenzhen to your door and we all know how well these packages are protected during shipping.

Voltlog #259 – InTheMail

Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time. We’re going to start with this small white box, which looks very uninteresting from the outside but contains something really nice, it’s a machined aluminium heatsink, designed specifically for the raspberry pi 4 and inside the box you get the two halves of the heatsink plus some mounting screws and silicone thermal pads.

There is a decent amount of aluminium in this heatsink, and we can see it has these rectangular raised islands for contact with the main chips on the board, so this is where the silicone pads will go. This is a completely passive heatsink and that’s what I was looking for but if you want more cooling power these are also actively cooled heatsink. feel like I should test this in a separate video to see how efficient it is when compared to a no heatsink solution which we already know doesn’t work well with the raspberry pi as it gets pretty hot. So we’ll leave this for a future video.

Voltlog #246 – What if we install a heatsink on the TPS61088 boost module?

In the previous video where I took a closer look at the TPS61088, I did some measurements of the output noise but I also ran the module up to the maximum specified output power of 12V 2A. It was to be expected that the losses would turn into heat and just the small size of the board would not be enough to dissipate all that heat safely so the boost chip reached a toasty 150 degrees Celsius and inevitably went into thermal protection.

There were two questions that people mainly left in the comments of that video. First people were curious if this module would behave differently if a heatsink was installed and also some people thought about using this module in a fixed configuration, because if you remember there is a chip on this module that will switch the output voltage based on quick charge spec, depending on what the load is requesting through that protocol but people might just want a simple fixed output. To this I would add a third question of my own, what is the real efficiency figure of this module, at the maximum output. 

Voltlog #245 – TPS61088 Boost Module Test (with QC3.0)

The real limitation for this small module to output the claimed 24W for longer periods of time is temperature. There is not enough thermal dissipation happening with this small pcb. Having a bigger pcb with more copper layers would help and it would probably allow this module to output continuously and prevent the TI controller chip from going into thermal overload. Even so I was impressed that running it into thermal protection several times did not do any damage the chip recovered on it’s own each time and no magic smoke escaped during these tests.

So all of this considered, this is probably one of the best dc-dc boost converter modules I got from China so far and I would recommend getting one of these if the specs meet your needs.

Voltlog #244 – InTheMail

Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time.

Voltlog #243 – TS80 VS KSGER T12 Soldering Iron Comparison

Welcome to a new Voltlog, yet another soldering iron comparison video and today it’s between the TS80 and the KSGER T12 station. Everyone knows the TS80, is quite a popular portable soldering iron, works with USB type C input, it needs a quick charge compatible adapter to reach full power and it’s quite a capable soldering iron. The drawback is the cost of the tips, it uses this proprietary type of tip and the cost is about $20 a piece.

On the other hand we have the KSGER soldering station which I reviewed in Voltlog #232. This station has a built in power supply and uses the well known T12 tips which are widely available on aliexpress, for example you can get KSGER T12 branded tips for about $3 a piece. I think that’s important, because I have 2-3 different tip shapes that I use regularly and maybe another 2 or 3 that I use occasionally for odd jobs. You can’t just rely on a single tip shape and purchasing the same number of tips for the TS80, is not going to be cheap.

Voltlog #200 – InTheMail

Welcome to a new voltlog, the first one in 2019 and what better way to start the year than with a InTheMail video the series that will touch both your passion for electronics and your bank account at the same time. As some of you might know I’ve recently created my patreon page so for those that would like to support me making these videos, you will find a link the description below, any pledge amount is appreciated, even 1$, just imagine half of my subscribers pledging 1$ a month. And if you can’t offer any donations, that’s fine too, my content will continue to be free.

Links for all of the items shown in the video will be in the video description, on youtube.

Voltlog #182 – InTheMail

Hello everyone and welcome to a new InTheMail the series that will touch both your passion for electronics and your bank account at the same time.