voltlog – Page 15

Voltlog #295 – Weekend Update

Welcome to a new Voltlog, this will be just a short weekend update video, to let you know what I’ve been doing in the past couple of weeks. So I’m staying at home and only going out for important stuff, which gave me more time to tinker and work on projects. I hope you are doing the same because social distancing is a good way to slow the spread of this disease.

One of the things I’ve been thinking of doing for a long time is a bench tool holder, the kind that will hold my tweezers, soldering iron tips, flux syringes, stuff like that. So far I’ve been keeping them in one of these pen holding cups but they fill up and it’s hard to grab the thing you need quickly. So I’ve started designing my own in Fusion 360, I included 6 deep pockets, 2 shallow ones in the front and 5 tubes for holding syringes.

The next thing I did with my 3d printer is related to the current pandemic, as you may know, medical staff in many countries which have been hit hard are lacking protective equipment, they just don’t have enough mask or suits or face shields, not to mention enough ventilators which are desperately needed for those in critical condition.

In parallel I’ve been designing the battery monitor circuit for the power drill I reviewed in Voltlog #285, this is the first revision of the PCB, the circuit works as expected but I’m still waiting on some parts to be delivered and I’ll do a separate video on this subject. It probably needs a second revision of the PCB because this one doesn’t quite fit in, the way I thought it will.

I also started designing a T10 automotive LED bulb. It’s using a linear constant current driver and some decent LEDs, because what I’m currently using in my car are the aliexpress bulbs which kinda start dying after a few months of usage. I’ll probably place an order for this panel today but who knows when I’ll receive it.

Voltlog #294 – InTheMail

Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time. Before I get started I’m gonna take a second to remind you to subscribe to the channel and hit the bell notification icon because that’s the only way you will know for sure when I upload new videos.

Depending on which part of the world you live in, you might be dealing with the same isolation measures as I am, the government is recommending we stay inside as much as possible here in Romania, to avoid contact with other people. So that gives me more time to work on projects, learn new stuff and of course discover and order stuff from the internet.

I’m gonna start with this notebook which has a retro looking leather cover, I think it’s quite neat looking, I’m not sure if this is real leather or not, description just said leather. I always keep a notebook around the workbench, it can be useful for drafting a quick schematic, some dimensions or just for writing down some measurements. Another cool feature of this notebook is the binder style clips you have inside, which allow you to insert or remove paper and what’s even nicer is that you can find this type of paper with different grid styles and they’re very affordable.

Voltlog #293 – Buying From Banggood and Ebay Tips & Tricks

Welcome to a new Voltlog, this is a continuation of Voltlog #291 where I shared some tips and tricks about buying from Aliexpress, if you haven’t seen that video, I will link it on screen right now. Today I’m gonna share my experience with buying from Banggood or Ebay. These are my secondary buying channels, some of the stuff you see in my mailbag videos comes from Banggood or Ebay.

Voltlog #292 – Hayear Full HD 34MP Microscope Camera Review HY-1139

Welcome to a new Voltlog, you might recognize this, the trinocular microscope which I reviewed in Voltlog #282, it’s a great tool to have especially if you start to feel your eyesight is getting weaker but also if you have good eyesight you can’t possibly solder 0402 passives comfortably or you can’t spot very small problems on soldering joints without something like this.

However I had an issue with the camera, the image is too black and so far there has been no solution provided by Banggood but I am still in contact with them and they’ve told me they are working with the supplier to find a solution but due to the whole Coronavirus (COVID-19) issue, there’s been delays.

So I’ve asked them to send another camera for review, it’s a Hayear branded microscope camera, it’s capable of up to 2K at 30fps and 1080P at 60fps, it has HDMI and USB 2.0 output as well as SD card storage support. The USB output is capable of 1080P at 30fps but that’s okay, cause I will be using this on it’s HDMI output on the 1080p 60fps setting.

Voltlog #291 – Buying From Aliexpress Tips & Tricks

Welcome to a new Voltlog, today I’m gonna share with you some tips and tricks about buying from Aliexpress and I might follow up with another video about Ebay and Banggood. I received requests for doing such a video several times as the subject was brought up and I think I can share a few useful things with you because as you may know, some of my most popular videos are my InTheMail videos where I show you the stuff I purchase from China and I get a lot of stuff which allowed me to learn a few tricks over the years.

Voltlog #290 – Riden RD6006 Output Noise Using Recommended Power Supply NVVV S-400-60

Welcome to a new Voltlog, this will be a rather short video cause I will only be addressing one short subject regarding the Riden RD6006 ripple noise. In my review of this power supply in Voltlog #284 I did measure the output ripple but that was measured while using a transformer to power the unit.

That transformer has very little output noise so the results we obtain can be considered best case scenarios but this may vary in practice, especially if you are using the recommended switch mode power supply. The output of that power supply may not be as clean as the one from the transformer so in this video I’m going to measure the output noise with the switch mode power supply installed.

I’m using the recommended NVVV 400W 60V 6.6A rated power supply, this is what RuiDeng officially recommends to use with their power supply kit. In Voltlog 284 part 3 I took a look inside this power supply so I will link that video on screen if you want to check it out.

Voltlog #289 – InTheMail

I must say I’m noticing delays in delivery of these packages from China, it started with orders placed mid January and I’m probably going to see some packages lost and never delivered so i recommend you keep an eye on your orders and request a refund when the protection time expires.

Voltlog #288 – New BLTouch 3DTouch Plastic Pin Sensor Upgrade

Back in 2018 I installed a Bltouch sensor on my Creality CR10 3d printer and I showed the process in Voltlog #177, that video is one of the most popular videos on the channel and now after using the printer with the upgrade for a couple of years I can clearly say it’s probably one of the best upgrades you can do to your 3d printer and it’s pretty cheap. I won’t go into too much detail about what the sensor does and how to install it because that is discussed in Voltlog #177.

However I did experience a downside after this upgrade, some users are reporting the same problem while others don’t face this issue. It’s important to note I am using a BLtouch clone called 3D touch, purchased from Aliexpress. It’s the type that has a metal push rod through the middle. The issue I’m having is a vibration noise coming from that metal pin vibrating inside the sensor when the printer moves on the Y axis. This issue might or might not be present on a genuine sensor or just another unit which might have tighter tolerances.

Voltlog #287 – Switching From Eagle To Kicad

Welcome to a new Voltlog, today I’m gonna talk a bit about my process of switching from EagleCad to Kicad. So i’ve been an EagleCAD user for years, I’ve practically learned how to do pcb layout in eagle cad so there is that emotional attachment to a piece of software because it’s what I used while developing this skill. And to be honest there wasn’t any better alternative years ago, Eagle was the first decent piece of cad software to offer a freeware license and it quickly became popular for hobbyists. It didn’t have all the bells and whistles of the expensive software like Altium or Candece but it did the job while being user friendly.

Since it quickly became popular for makers and hobbyists it also meant there was an abundance of support on the forums as well as many user generated scripts and libraries freely available. It was similar to the popularity Arduino got but it was never open source and if you needed some extra features like 4 layer layout or pcb sizes larger than 8x10cm you needed to pay for a license.

Voltlog #286 – How Is The Coronavirus Affecting PCB Production?

Welcome to a new Voltlog, I have a couple of projects in the pipeline right now that require PCBs and as usual I will be getting them from JLCPCB who have been sponsoring my videos for a while now and even if they weren’t I would still be ordering from them because I like how their service runs. But the problem right now as you may know is the Coronavirus infection. In order to contain the spread of the virus, companies in China have moved to a work from home scenario with only minimal required personnel present on site.

This coupled with the extended holiday which was issued after the spring festival means decreased manufacturing capacity which leads to long lead times as customers line up to get their PCBs manufactured.

So this video is more an update on the current situation because I am in contact with JLCPCB and I want to give you some info on the expected delays for pcb orders. Right now they offer production of 2 layer pcbs as well as smt assembly service and stencil production service but 4 layer, 6 layer and ENIG coated pcb manufacturing has been suspended until further notice.